Quick Share
XR360E rotary drilling rig
Are you still hesitating? You can contact our product experts first. Contact us!
Product classification
Keywords
- PRODUCT DETAILS
-
XR360E主要技术参数
Main Technical Specification最大钻孔直径
Max. Drilling diametermm Φ2600 最大钻孔深度
Max. Drilling depthm 91 工作尺寸
Working condition dimensionmm 12500*4900*25820 工作重量
Overall weightt 113 履 带
Crawler履带宽度
Width of crawlermm 3500-4900 履带板宽
Shoes Widthmm 800 履带长度
Length of crawlermm 6465 接地比压
Ground pressurekPa 125 行走速度
Traveling speedkm/h 0~1.6 钻桅
Mast左右倾角
mast left/right° 4 前倾
mast front° 5 后倾
mast back° 15 动力头
Ratory drive扭矩
Max. output tortuekN·m 360 转速
Rotational speedr/min 6~27 油缸加压
Crowd cylinder加压油缸最大加压力
Max. Pushing forcekN 300 加压油缸最大提升力
Max. Pulling forcekN 350 加压油缸行程
Max.strokemm 6000 主卷扬
Main winch主卷扬最大单绳速度
Max. single-rope speedm/min 60 主卷扬钢丝绳直径
Diameter of the steel wire ropemm 36 主卷扬提升力
Lifting forcekN 370 副卷扬
Auxiliary winch副卷扬提升力
Lifting forcekN 100 副卷扬最大单绳速度
Max. single-rope speedm/min 40 副卷扬钢丝绳直径
Diameter of the steel wire ropemm 20 发动机
Engine型号
Model/ TAD1353VE 功率
Rated powerkW 345 液压系统
Hydraulic system最大流量
Maximum Flow RateL 2×380L/min+180L/min 最大工作压力
Max. working pressure of main pumpMPa 33
XR360E rotary drilling rig
Product classification
Keywords
PROVIDE HIGH-QUALITY SECOND-HAND CONSTRUCTION MACHINERY AND EQUIPMENT TO CUSTOMERS AROUND THE WORLD
Annual Sales Volume
Selling to more than 60 countries
Cumulative service customers
FAQ
A common fault troubleshooting for engine failure to start
Rotary Drilling Rig Engine Failure to Start (Fuel Pump Fault)
I. Basic Case Information
- Product: Rotary Drilling Rig
- Model: XCMG XR220D
- Working Hours: 3400
II. Fault Phenomenon
The engine fails to start.
III. Fault Analysis
- The starting motor circuit and key switch circuit were inspected and found to be normal.
- The diesel oil circuit from the fuel tank to the engine was checked for blockage, along with the fuel filter element; both were normal.
IV. Troubleshooting Process
- The oil inlet pipe of the fuel pump was removed, and a large oil output was observed. The hard pipe on the engine common rail was removed for inspection, and a small oil output was found.
- The high-pressure fuel pump was disassembled and cleaned, revealing severe internal wear and impurities such as oil sludge.
- The worn eccentric shaft inside the pump was replaced, and internal impurities were cleaned; the engine started normally afterward.
V. Fault Cause (Conclusion)
Severe internal wear of the fuel pump resulted in failure to build up sufficient fuel pressure, which could not meet the fuel supply pressure required for normal engine start.It is recommended that the customer use higher-quality diesel, replace the filter element in a timely manner, and clean the fuel tank regularly.
What are the regular maintenance tasks for the website?
What are the regular maintenance tasks for the website?What are the regular maintenance tasks for the website?What are the regular maintenance tasks for the website?What are the regular maintenance tasks for the website?
What are the regular maintenance tasks for the website?
What are the regular maintenance tasks for the website?What are the regular maintenance tasks for the website?What are the regular maintenance tasks for the website?What are the regular maintenance tasks for the website?
What are the regular maintenance tasks for the website1?
What are the regular maintenance tasks for the website?What are the regular maintenance tasks for the website?What are the regular maintenance tasks for the website?What are the regular maintenance tasks for the website?What are the regular maintenance tasks for the website?
RECOMMEND PRODUCTS
Content update in progress
PRODUCT CONSULTING
Note: Please leave your email address and our professionals will contact you as soon as possible!
Service Hotline
Address: Room 401, 4th Floor, Office Building, No. 13, Baoyuan Road, Guangxi-ASEAN Economic and Technological Development Zone
